MINI SERIES
The product group of I/O modules MINI series has been designed to complement the I/O modules of the MIX series. Unlike the MIX series, the MINI line is dedicated to all applications, where hand operating switches are required. The built-in light, cooling and heating algorithms make them applicable as the standalone controllers. Additionally, the modules support time relay modes dedicated to present detectors. Like in case of the MIX series modules, MINI series is factory-equipped with the two most popular open communication protocols: Modbus (ASCII, RTU, TCP/IP) and BACnet (MS/TP, IP), which are selected using DIP switches. There are two versions of the modules: with RS485 interface and with Ethernet and RS485 interfaces. Devices with Ethernet and RS485 interfaces have the added functionality of “Modbus Gateway TCP/IP to Modbus ASCII/RTU”, enabling for the connection of additional modules /devices which communicate via Modbus RS485. The Modbus Gateway functionality is active also for devices configured as BACnet IP modules. IP modules, communicating either in Modbus or BACnet, are always master units on the network. One major advantage of supporting the modules with open communication standards is the versatility to install them in both new and completed installations, as part of an existing BMS.
Key Features
- 14 different types
- Small dimension
- Manual override switches
- Built-in light, cooling and heating control modes
- Present sensor support modes
- All Digital Inputs work as fast counters up to 100Hz
- Universal Inputs have 16-bit resolution which increases the accuracy of measurement
- Wide range of supported temperature sensors in Celsius and Fahrenheit degrees (NTC, PT1000 etc.)
- Automatic detection of the signal type in the case of Universal Inputs
- Digital Outputs 230 V AC max. 3 A or 8 A allow for direct control without additional relays
- Triac Outputs: 0,5 A @ 24 V AC, 0,5 A @ 230 V AC
- Analog Output with max. 20 mA load per channel allow direct control of relays (12 V DC) or SSR with PWM support
- LEDs indicate the status of inputs and outputs
- Supports open standards: BACnet or Modbus
- Built in Modbus Gateway TCP/IP to RS485
- 1x Fast Ethernet
- Simple and fast addressing from 1 to 99
MIX18
MIX38
MIX SERIES
The product group of I/O modules of the MIX series has been designed for building distributed control systems using JACE or AAC20 devices. All the MIX Series modules have been equipped with the most commonly used types of I/O in building automation (MIX of all types of I/O in one unit). The modules are factory-equipped with the two most popular open communication protocols: Modbus (ASCII, RTU, TCP/IP) and BACnet (MSTP, IP), which are selected using DIP switches. There are two versions of the modules, namely: modules with interface RS485, and modules with interfaces 2x Ethernet and RS485. Devices with interfaces 2x Ethernet and RS485 have the added functionality of “Modbus Gateway TCP/IP to Modbus ASCII/RTU”, enabling you to connect additional modules/devices that communicate via Modbus RS485. The Modbus Gateway functionality is active also for devices configured as BACnet IP modules. IP modules, communicating either in Modbus or BACnet, are always master units on the network. One major advantage of supporting our modules with open communication standards is the versatility to install them in both new and completed installations, as part of an existing BMS. Addressing the modules is via rotary switches, which facilitates and accelerates the process of commissioning the system. Built-in mini USB allows for initial configuration of the unit without power supply.
Key Features
- A large number of all types of I/O
- All digital inputs work as fast counters up to 100 Hz
- Universal inputs have 16-bit resolution which increase the accuracy of measurement
- Wide range of supported temperature sensors
- (NTC, PT1000 etc.)
- Automatic detection of the signal type in the case of universal inputs
- Digital outputs 230 V AC max. 3 A allow direct control without additional relays
- Analog output with max. 20 mA load allow direct control of relays (12 V DC) or SSR with PWM support
- LEDs indicate the status of inputs and outputs
- Supports open standards: BACnet or Modbus
- RS485 communication port, half duplex
- 2x Fast Ethernet with built in switch
- Built in Modbus Gateway TCP/IP to RS485
- Simple and fast addressing from 1 to 99
MAX SERIES
Multiprotocol I/O Module with a MAX number of Digital Outputs – a powerful addition to any building automation system.
The MAX-RS series offers a range of modules, including a 24 digital inputs module and a 12 digital outputs module with hand control, both featuring open protocols such as BACnet and Modbus. Open protocols standard offers the versatility of installing the modules in both new and existing facilities, whether it is a system expansion or a retrofit. The maximum number of the most popular types of inputs or outputs allows the module to be a versatile controller extension, whether in a small or large facility.
Key Features
24 Digital Inputs
The 24 digital inputs module is designed for monitoring data in data centers and HVAC applications. Its compact design allows for multiple inputs to be packed into one housing, resulting in shorter engineering time, faster integration, and easier commissioning.
12 Digital Outputs
The 12 digital outputs module is ideal for HVAC applications, allowing for a direct control of up to 3A loads per single digital output. With HOA switches, manual override of each output is possible, ensuring ultimate control.
MAX-RS Series – 24I, 12O-H
All MAX-RS series modules are equipped with commonly used types of I/Os in building automation, and support open communication protocols including Modbus RTU/ASCII and BACnet MS/TP selectable by a DIP switch. The modules are designed to create distributed control systems by extending the capabilities of building controllers like AAC20, iSMA-B-J8, or MAC36NL with inputs and outputs using serial bus connections.
MAX-IP Series – 24I-IP, 12O-H-IP
All MAX-IP series modules are equipped with commonly used types of I/Os in building automation, and support open communication protocols including Modbus TCP/IP and BACnet IP. The modules are designed to create distributed control systems by extending the capabilities of building controllers like AAC20, iSMA-B-J8, or MAC36NL with inputs and outputs using IP connection. The modules feature two Fast Ethernet ports that work in a switch mode, allowing for a daisy chain connection of multiple units. Additionally, the modules have an RS485 interface that acts as a Modbus TCP/IP to Modbus RTU/ASCII gateway, enabling the connection of extra devices/modules that communicate as servers (slaves) on the serial bus. Commissioning the system is facilitated by the rotary switches used to address the modules.
24I, 12O-H
24I-IP, 12O-H-IP
W0202
W0202 has been built to allow extension of RS485 bus using wireless technology wherever use of network cable is impossible or unprofitable. Use of two W0202 allows to build the wireless ‘bridge’ for the RS485 by building wireless remote island (one or more) for devices communicate via Modbus RTU/ASCII – eg. MIX series I/O modules or MINI series I/O modules. W0202 in addition to the RS-485 port and wireless port is equipped with 2x SI (Special Inputs) and 2x DO (Digital Outputs), which allow to use device as an I/O module or light controller communicating in Modbus RTU/ASCII. Implemented algorithm in the processor allows user to choose one of 3 different modes:
• Modbus Bridge
• Modbus Bridge and I/O module (both DO work independent of the state of SI)
• Modbus Bridge and light controller (DO work in direct connection with SI)-there are 3 sub–modes of operation: Monostable Switch, Bistable Switch, Time Relay (PIR).
W0202 is also equipped with a micro USB port which allows to configure the device without the use of an external power supply (the device is powered through the USB port). This solution gives you an easy way, using 2 laptops, carry out the tests within the existing facility.
Key Features
- High transmit power and high sensitivity
- No license required for the radio band
- USB for configuration
- 1x RS485 port (Modbus)
- 2x Special Inputs: voltage, resistance, dry contact and fast counter up to 100 Hz save in EEPROM
- 2x Digital Outputs: relay max. 3 A, 230 V AC/30 V DC
- LEDs indicating the state of the SI and DO
- Fast processor with ARM core
- 3 different operating modes
SFAR-1M
The SFAR-1M series of I/O modules is the generation of devices for the industrial automation and robotics. These devices are one of the smallest I/O modules available on the market with 1M enclosure size. There are 7 different types with the range of built-in I/O from 2 to 4, which makes these modules perfect solution for measuring a small number of signals at one point. Built-in RS485 interface allows to easy connection over Modbus RTU/ASCII protocol with a PLC makes the modules an external I/O. The use of 32-bit ARM core processor provides fast processing and communication with the baud rate from 2400 to 115200 bps. All the modules are equipped with a set of LEDs used to indicate the status of inputs and outputs useful for diagnostic purposes and helping to find errors. Built-in mini USB allows for initial configuration of the unit without power supply.
Key Features
- 7 different types
- Digital Inputs work as fast counters up to
- 1 kHz
- Version with FRAM memory for counters
- Digital Inputs supports encoders
- Analog Inputs measuring current or voltage
- Temperature Inputs support the most popular sensor types: PT100, PT500, PT1000, NI100, KTY81-110 (2 and 3- wire)
- Temperature Inputs support the most popular thermocouples types: J, K, T, N, S, R, B
- Relay outputs up to 10 A
- Analog Outputs operating as current or voltage
- Modbus RTU/ASCII communication
- Up to 128 modules on the bus
- 1 kV galvanic isolated I/O
- Built-in mini USB type B port for configuration
SFAR-S
The SFAR-S series of I/O modules is the generation of devices for the industrial automation and robotics. The characteristic feature of these modules is slim type of enclosure which needs very small space in the cabinet while offering up to 16 I/O. Built-in RS485 interface allows to easy connection over Modbus RTU/ASCII protocol with a PLC makes the modules an external I/O. The use of 32-bit ARM core processor provides fast processing and communication with the baud rate from 2400 to 115200 bps. All the modules are equipped with a set of LEDs used to indicate the status of inputs and outputs useful for diagnostic purposes and helping to find errors. Built-in mini USB allows for initial configuration of the unit without power supply. Dedicated IP module SFAR-S-ETH with Modbus TCP/IP to RS485 gateway, enabling use of SFAR-S series modules in the applications where the IP connectivity is required.
Key Features
- 12 different types
- Digital Inputs work as fast counters up to
- 1 kHz
- Version with FRAM memory for counters
- Digital Inputs supports encoders
- Analog Inputs measuring current or voltage
- Temperature Inputs support the most popular sensor types: PT100, PT500, PT1000, NI100, KTY81-110 (2 and 3- wire)
- Temperature Inputs support the most popular thermocouples types: J, K, T, N, S, R, B
- Relay outputs up to 10 A
- Analog Outputs operating as current or voltage
- Modbus RTU/ASCII communication
- Up to 128 modules on the bus
- Dedicated TCP/IP gateway device SFAR-S-ETH
- 1 kV galvanic isolated I/O
- Built-in mini USB type B port for configuration